QMS 2001 Průvodce nastavením

QMS® 2001 Knowledge System Setup Guide1800324-001C

9 4 Unfold the scanner-tray extension and slide the scanner-tray flaps (under the tray) together. 5 Install the output tray: set the two tabs on the

10 2 In the COM Ports screen, see which COM settings are in use (unused ports are labeled N/A). In the table below, circle the cell in the left-most

11More information about COM settings is provided on page 23. You should also check your fax modem documentation for any instructions specific to your

12 9 Fit the fax modem’s retaining bracket into the com-puter’s interface panel and press the fax modem firmly into the 16-bit slot. 10 Fasten the

13 2 At the computer, use the telephone cable (included with the fax modem) to connect the jack labeled “Line” on the fax modem to a phone jack in th

14 2 From the Program Manager File menu choose Run. 3 In the Run dialog box, type a:\setup.(If the disk is in another drive, substitute the letter o

15Note: If the Fax Server is not running when QMS Manager is started, then QMS Manager startup will be delayed for 15 to 30 seconds while the Fax Serv

16 XÎÝ@ÎkÌÎkÌ,ÂÎk Ì  Ýk 1 In Windows, double-click the Control Panel icon (usually in the Main program group). 2 In the Control Panel wind

17.kÅÎkÂÌ@bÌ1kÅÎÌÎ kÌ/àÅÎkRegister your 2001 and try out the system at the same time by faxing the registration document to QMS: 1 In QMS Manage

18kXÎÌÎk ÌÞkbkÌ/àÅÎkÌ,2Caution: Before connecting the system, make sure it’s off. 1 Use the telephone cable included with the fax mode

1ÎÂb×XÎThis document explains how to set up the QMS 2001 Knowl-edge System, an integrated information management system for Windows environments

19 4 Connect the 2001 to a grounded electrical outlet.Note: Make sure the electrical outlet you connect the system to is a properly grounded (earth c

20 8 Choose Send from the QMS Manager button bar to open the Send Document dialog box. 9 In the Send Document dialog box, select QMS Regis-tration

21ÂÌx Â @ÎÌÌ $/Ì@bÌ9bÞŲ ²²MS DOS and Microsoft Windows documentation—Using the QMS Manager software is easy, but like any Windows app

22xÌ;×Ì@ÝkÌ1Â×Nk²²²If you have difficulties setting up the 2001, try the following: 1 Make sure interface cables and power cords are secure. 2

23-!/Ì9ÂbÞbkÌ$xxXk ÅUnited States/Latin AmericaOne Magnum PassMobile, AL 36618(205) 633-4300*Fax (205) 633-4866*Latin America Fax (205) 639-3347

24tics (MSD)—described in step 1 in “Installing the Fax Modem in the Computer” on page 9. Unassigned IRQs are labeled “Reserved” in MSD.)If you curren

25Manual NoticeQMS, Inc. reserves the right to make changes to this manual and to the equipment described herein without notice. Considerable effort h

2ÅÎ @@ÎÌ,ÂXkb×ÂkÅÌxÌà × ÁÂkÌ Å Î@ Ì@Ì Þ kb kÌ/àÅÎ k Ìk Â k Â@Ì× β² ²Follow the instructions in this guide to...Make su

3!×Ì/àÅÎkÌ.k·×ÂkkÎÅÌxÂÌÎkÌÕææ¥Ì,kÂkÂ@Ì3ÎYou’ll need at least the following levels of hardware and soft-ware installed to use the Know

49@ ÎÁÅÌX ×bkbÌÌ Îk Ì/k ÎIf you’re missing anything, report it to your QMS vendor.ÌÞkbkÌ/àÅÎk ÅÌX kÌÞÎ²²²QMS 2001 Knowledge

5X @ÎÌ.k ·×Âk kÎÅThe QMS 2001 Knowledge System should be located...ÅÎ@  ÌÎ kÌ,Î  Xb×X Î ÂÌ3ÎÌ2Caution: The belt inside the PCU

6 2 Remove the PCU from its packaging and remove the red tab (and attached piece of polystyrene) at each end of the PCU. 3 Holding the PCU by its tw

7ÅÎ @ÌÎkÌ1k ÂÌ@ÂÎÂbk 1 Remove the toner cartridge from its packaging.2Caution: Don’t touch the roller inside the toner cartridge. 2 Hol

8 5 Push the toner cartridge firmly in place. 6 Close the toner-cartridge access door.ÅÎ@ Ì ÎkÌ!kb@Ì 1Â@àÅ 1 Remove any tape or packing ma